Apex Local LLC
HOMESERVICESWORKABOUTPRICINGBLOGREVIEWSBOOK NOW
Free Estimate

Flat-rate menu

Flat-rate menu

Apex Local Flat-Rate Service Menu

Handyman & home repair · Mukilteo · Everett · Lynnwood · Edmonds · Mill Creek · Bothell · Marysville · Shoreline

Version 1.0 · Effective October 2026 · Prices subject to change

Apex Local LLC · operations@apexlocal.us · 8619 53rd Pl W, Mukilteo, WA 98275 · apexlocal.us · (206) 739-1809 · Licensed, bonded & insured · WA L&I #APEXLLL749PO

Know the price before we start. Every item below is a flat price for the work described. If something isn't on the menu, you'll get a written quote with a not-to-exceed ceiling before any work begins. We text when we're on the way, arrive inside a 2-hour window, clean up, and back our work for 12 months.

How pricing works

Policy What it means for you
Visit minimum: $129 Covers the trip within our service zone and your first hour of labor, or any menu items adding up to $129. Menu prices already include the trip. If your items total less than $129, the visit is $129. Tip: bundle small jobs into one visit.
Service call (diagnose / measure only): $59 When a visit is just for diagnosis, measuring or an on-site estimate and no work is done that day. Photo and video estimates are always free.
Return visit: $69 per extra trip Some jobs need a second trip (e.g., drywall that must dry before sanding and paint). When a job needs it, the return trip is already built into the menu price (see "2-visit" items). The $69 applies only to extra trips you request or that are needed for reasons on your side (materials not on site, area not ready, no access). It covers the trip plus up to 20 minutes on site; more time is billed at the hourly rate. Never charged for our own callbacks or warranty work.
Labor beyond the menu: $89/hr After the first hour, billed in 30-minute increments.
Materials Use your own, or we buy them at receipt cost + 10% sourcing (min. $15). Receipts are attached to your invoice.
Service zone No extra charge: Mukilteo, Everett, Lynnwood, Edmonds, Mill Creek, Mountlake Terrace, Brier, Bothell, Shoreline, Marysville, Lake Stevens, Snohomish. Extended zone +$29 per visit: Arlington, Monroe, Stanwood, Lake Forest Park, Kenmore, Woodinville, north Seattle.
Hours Mon–Sat at standard prices. Sunday, holiday or after 6 pm: +$59 per visit. Same-day urgent (when available): +$75.
On-time promise 2-hour arrival window plus an "on the way" text. More than 30 minutes late without notice = $25 off.
Cancellation Free with 24 hours' notice. Under 24 hours: $39 (waived the first time).
Warranty 12-month workmanship warranty on everything we do.
Taxes Prices are before Washington retail sales tax, which applies to most repair labor and materials.

Mounting & installation

# Service Price What's included Typical time
M1 TV wall mount, up to 65" $119 Your bracket, mounted into studs; level; surface cord cover 1–1.5 hr
M2 TV mount, 66"+ or brick / stone / over fireplace $179 Masonry anchors or heavy-duty hardware, level, cord cover 2–2.5 hr
M3 Paint-matched surface cable raceway +$39 Add-on to M1/M2, up to 6 ft 45 min
M4 Curtain rods or blinds $79 first window, +$29 each additional Measure, level, anchor, hang 45 min first
M5 Shelves (up to 3 floating or bracket shelves) $109 Stud or rated-anchor mounting, level 1 hr
M6 Art and mirrors, up to 5 pieces (≤ 50 lb each) $89 Layout help, level, rated hardware 1 hr
M7 Heavy mirror or art (over 50 lb) $119 Cleat or heavy-duty mount 1–1.5 hr
M8 Grab bar $109 first, +$49 each additional; on tile +$29 per bar Into studs or blocking-rated anchors; load-tested 1 hr first
M9 Interior stair handrail, up to 12 ft $199 + rail Brackets into studs, cut to length, returns 2 hr
M10 Furniture assembly: small item (chair, nightstand) $55 each Assembly and placement (visit minimum applies) 30–45 min
M11 Furniture assembly: standard (dresser, bookcase, desk) $99 each Assembly, anti-tip strap installed 1–1.5 hr
M12 Furniture assembly: large (wardrobe system, storage bed) $179 each Assembly, anchoring, packaging hauled to your bin 2–3 hr
M13 Closet rail/track system, up to 6 ft $169 Track or rail system installed and leveled 2 hr
M14 Over-the-range microwave (plugs into an existing outlet) $149 Remove old unit, mount new on existing bracket/vent 1.5 hr
M15 Garage ceiling storage rack (up to 4×8 ft) $139 Joist-mounted per manufacturer specs 1.5 hr
M16 Battery-only smoke / CO alarms (up to 4) $69 Install or replace, test, date-label 45 min

Doors, windows & cabinets

# Service Price What's included Typical time
D1 Interior door adjustment (sticking, latch, hinges) $79 first, +$39 each additional Hinge shim/tighten, strike adjust, light plane if needed 45 min first
D2 Lockset, deadbolt or lever (existing holes) $79 first, +$35 each additional Your hardware installed and tested 30–45 min first
D3 Bifold or bypass closet door repair $99 + parts Realign, replace pivots/guides 1 hr
D4 Sliding patio door tune-up $149 + rollers Clean track, adjust or replace rollers, lock alignment 1.5 hr
D5 Exterior door weatherstrip + door sweep $119 + materials Remove old, install new, check latch seal 1–1.5 hr
D6 Pre-hung interior door replacement (same size) $289 + door Remove old, set, shim, case one side, hardware 3 hr
D7 Screen or storm door install (hinged door you bought) $89/hr labor Install, closer, latch adjust 2–2.5 hr
D8 Window re-screen (standard size) $45 each + $89/hr labor, $129 minimum job charge New screen mesh and spline 20–30 min each
D8a New custom window screen $75 each Custom-built screen —
D8b Pet-resistant or solar mesh +$30 per screen Upgrade mesh —
D9 Pet door in an existing door $149 Cut, install, seal 1.5 hr
D10 Sliding patio screen door re-screen $99 per door New mesh and spline —
D11 Install customer-bought sliding patio screen door Labor only: $89/hr, $129 minimum job charge Install your door —
D12 Cabinet door hinges: adjust or replace (up to 6 doors) $89 Align gaps, replace worn hinges (parts extra) 1 hr

$129 visit minimum applies to screen jobs.

Drywall & paint

Drywall compound has to dry. A 1-visit item leaves a primed, ready-to-paint patch. A 2-visit / finished item includes the return trip to sand, add a final coat, prime and paint with your paint, and that return trip is already in the price.

# Service Price What's included Typical time
W1 Small patch, up to 6": 1-visit, ready to paint $139 Patch, quick-set compound, texture match (best effort), prime 1.5 hr
W2 Small patch, up to 6": 2-visit, finished $229 W1 + return visit: sand, final coat, prime, paint 1.25 hr + 45 min
W3 Medium patch, 6"–16": 2-visit, finished $279 Cut-in patch, tape, two coats, texture, prime, paint 2 hr + 45 min
W4 Large patch, 16" up to 4×4 ft: 2-visit, finished $389 New drywall section, tape, coats, texture, prime, paint 3 hr + 1.25 hr
W5 Each additional patch, same room and visit +$45 small · +$79 medium Done alongside the first patch —
W6 Nail pops and hairline cracks, one room $129 Reset fasteners, fill, prime (ready to paint) 1–1.5 hr
W7 Ceiling water stain: seal and spot-paint (up to 4 sq ft; leak already fixed) $149 Stain-block primer, ceiling paint blend 1–1.5 hr
W8 Paint touch-ups with your paint (up to 2 hours) $179 Walls, trim, doors; drop cloths and cleanup 2 hr

Larger patches, ceilings over 10 ft and full-room painting get a written not-to-exceed quote.

Caulking, tile & wet areas

# Service Price What's included Typical time
C1 Tub or shower re-caulk: standard tub surround $159 Remove old caulk, mildew treatment, new silicone (24-hr cure) 1.5–2 hr
C2 Re-caulk: walk-in shower with glass $189 Same as C1, plus glass and door seams 2–2.5 hr
C3 Kitchen or bath counter / backsplash caulk $79 (+$45 as an add-on) Remove and replace bead 45 min
C4 Grout repair, small area (≤ 10 sq ft) $179 Remove damaged grout, regrout, seal 2 hr
C5 Shower door adjustment / sweep replacement $109 + sweep Realign, new sweep or seal 1 hr

Exterior & seasonal

# Service Price What's included Typical time
E1 Gutter cleaning, single-story (up to 150 linear ft) $159 Clear gutters, flush downspouts, bag debris 1.5–2 hr
E1b Gutter cleaning, two-story (up to 200 linear ft) $299 Clear gutters, flush downspouts, bag debris 3–4 hr
E2 Fence repair, up to 6 boards or pickets $149 + materials Remove, replace, fasten 1.5 hr
E3 Gate sag fix $129 Anti-sag kit or hinge/latch rework 1–1.5 hr
E4 Deck board replacement, up to 3 boards $189 + materials Remove, replace, fasten, seal cut ends 2 hr
E5 Wood rot: small trim or sill repair (up to 2 ft) $199 Remove rot, epoxy consolidate/fill, shape, prime 2 hr (+ cure)
E6 Exterior caulk, up to 6 ground-floor windows or doors $189 Remove failed caulk, new exterior sealant 2 hr
E7 Dryer vent cleaning (accessible run, up to 10 ft) $99 Brush and vacuum the run, clean the exterior hood 45–60 min

Roofs: moss removal by hand brushing/scraping only. No chemical moss treatments. Quoted after a safety check. Two-story gutter cleaning beyond 200 linear ft and exceptional or tall-ladder work are quoted after a safety check.

Demo & Haul-Away

An asbestos survey is required before any demo work, whatever the home's age (see Demo & haul policies). Homes built before 1978 also follow EPA lead-safe rules.

Light, non-structural tear-out with the cleanup and dump run included. Every price below includes floor and doorway protection, bagging, carry-out, the haul to a transfer station, disposal fees up to the weight shown, and a HEPA-vacuum broom-clean. Demo & haul visit minimum: $199 (trip, up to 1 hour of work, and one dump run with disposal up to 360 lb).

# Service Price What's included Typical time
H1 Drywall demo, one wall (one side, up to 100 sq ft) $249 · +$139 each additional wall, same visit Remove drywall to the studs, pull fasteners, haul up to 400 lb 1–1.5 hr
H2 Drywall demo by the square foot (rooms, larger areas) Walls $1.60/sq ft · ceilings $2.40/sq ft · stairwells $2.40/sq ft (min. $249) Measured wall/ceiling face; haul up to ½ load included. Insulation removal +$0.60/sq ft. Example: 12×12 room, walls only, after door/window openings (~340 sq ft) ≈ $545 ~120 sq ft/hr (walls)
H3 Basement staircase drywall, both side walls (no ceiling) $579 Up to 240 sq ft combined, one flight (≤ 14 steps); tread protection, handrail removed and set aside, stud faces cleaned of fasteners, haul included 4.5–5 hr, 1 visit
H4 Cabinet & vanity removal Vanity up to 48" with top $209 (+$109 with other demo) · Kitchen/built-in cabinets $22 per linear ft of run (uppers and bases counted separately; min. $249) · laminate countertop +$10/linear ft Unfasten, remove, haul. Plumbing and appliances must be disconnected and capped by a licensed plumber/electrician first. Stone tops: quote (2-person lift) Vanity ~1 hr; 20 ft of cabinets ~3.5 hr
H5 Carpet & pad removal $199 first room (up to 200 sq ft) · +$89 each additional room · stairs +$9/step Cut, roll, pull pad, staples and tack strip; haul 45–60 min per room
H6 Floor removal ⚠ Floating laminate / click vinyl / engineered: $1.75/sq ft (min. $249) · HEAVY: ceramic or porcelain tile on thinset: $6.00/sq ft (min. $449) Remove to subfloor, scrape high spots, haul. Mortar-bed tile, glued hardwood, concrete and any sheet vinyl/linoleum or 9"/12" tile from a pre-1981 home: written quote only, after an asbestos survey 100 sq ft laminate ~1 hr; 100 sq ft tile ~4.5 hr
H7 Fence & deck section demo Fence: up to 16 ft (2 sections) $319 · +$99 each additional 8-ft section · concrete-set posts pulled +$45/post (or cut flush, free) · Ground-level deck (≤ 30" high, ≤ 200 sq ft) $8.50/sq ft (min. $649) Dismantle, cut down, haul. Footings and concrete stay unless quoted. Decks attached with a ledger: we cap the ledger holes with flashing tape; siding repair quoted separately 16-ft fence ~2 hr; 100 sq ft deck ~6 hr
H8 Small shed teardown (up to 120 sq ft of roof area) Metal or resin kit shed $449 · wood shed up to 8×10 $899 · wood up to 10×12 $1,149 Disassemble, remove roofing, haul (up to 3 loads). Slab or blocks stay. Requires the asbestos survey described below 3–8 hr
H9 Appliance haul-away (fridge, freezer, washer, dryer, range, dishwasher) $69 each on any Apex visit · +$25 for refrigerant units (fridge/freezer/AC) Disconnected first (gas and hardwired units by a licensed trade); carried out; taken to a recycler that recovers refrigerant 20–30 min each
H10 Haul-away by load size (Apex trailer, about 6 cubic yards) Minimum $59 (add-on) · ¼ load $219 · ½ load $339 · Full load $549 Min ≤ ½ cu yd / 200 lb · ¼ ≈ 1.5 cu yd / 500 lb · ½ ≈ 3 cu yd / 1,000 lb · full ≈ 6 cu yd / 2,000 lb. Loading by our crew, haul, scrap metal and cardboard sorted for recycling, disposal up to the weight shown 20 min to 2 hr on site
H11 Construction debris haul, at-cost disposal option $89/hr (PM $85) for loading and dump-run time, min. $129, plus the transfer-station scale ticket at cost, no markup Best for large or mixed piles where weight is hard to predict. The scale-ticket photo is attached to your invoice Billed by time
H12 Strip-out hour (non-structural fixtures) $199 first hour (incl. minimum haul) · $89 each additional hour Shelving, closet systems, mirrors, shower doors, towel bars, blinds, baseboard/trim (salvage on request) 1 hr blocks

Haul-away (H9–H11) is only for items and debris from work we do at your property. We don't offer stand-alone hauling; we're happy to refer a licensed hauler.

Disposal fees are never discounted or marked up. Extended-zone visits add $29.

Demo & haul policies

  • Disposal fees, two ways, your choice on the quote.
    • Built-in (default): menu prices include transfer-station fees up to the weight listed. If the scale ticket shows more weight, the overage is billed at cost with the ticket photo (2026 Snohomish County self-haul rate: $160/ton plus the 3.6% state refuse tax, $30 minimum).
    • At cost: time plus the scale ticket at cost, no markup (H11).
    • Recyclables (scrap metal, cardboard) go to recycling; donations go to a local charity drop when items are reusable.
  • What we don't haul: paint, solvents, fuels, propane, batteries, chemicals, medical waste, or any material known or presumed to contain asbestos. We can point you to the county household hazardous waste program.
  • Asbestos survey before any demo (Washington and Puget Sound Clean Air Agency rules).
    • In Snohomish and King counties, the Puget Sound Clean Air Agency requires an asbestos survey of suspect materials before any renovation, regardless of the home's age, and an AHERA-certified inspector's survey before any demolition of a structure (including sheds).
    • Washington law (RCW 49.26.013) also requires the property owner to give the contractor a written good-faith asbestos inspection report, or a written statement, before demo starts. We can't start without it.
    • The one owner exception: owners of an owner-occupied single-family home may do their own renovation survey. For rentals, condos and all demolitions, an AHERA inspector is required.
    • Higher-risk materials include drywall joint compound and wall/ceiling texture, popcorn ceilings, sheet vinyl and floor tile with mastic, and duct and pipe wrap. State rules presume vinyl and asphalt flooring installed in 1980 or earlier contains asbestos until tested.
    • If testing finds asbestos, a certified asbestos abatement contractor must remove it before we do any work.
  • Lead paint (homes built before 1978). Washington runs the EPA Renovation, Repair and Painting (RRP) program through the Department of Commerce. Demolishing painted surfaces in pre-1978 homes is always covered, no matter how small the area. That work needs an RRP-certified firm with a certified renovator, lead-safe containment and cleaning, and the "Renovate Right" pamphlet given to the occupant beforehand. The exception is surfaces tested lead-free by a certified inspector or renovator.
  • No structural or load-bearing work. We remove finishes (drywall, flooring, cabinets, trim) and freestanding or small structures only. We never remove or cut studs, joists, beams, posts, headers, shear walls or anything that might be load-bearing. Wall removal, openings and structural repairs go to a general contractor or engineer.
  • Utilities behind walls are made safe by licensed trades first. Any wiring, outlets, switches, fixtures, plumbing, gas or ducts in the demo area must be disconnected and capped by a licensed electrician, plumber or gas fitter before or during our visit. We stop work if we find live or unidentified utilities. We can coordinate the partner.
  • Permits. Interior finish removal usually doesn't need a permit, but deck, shed and exterior work can, depending on the city. We'll tell you if we think one applies; the property owner obtains it.

Licensed-trade work we don't perform (we'll connect you with a licensed partner)

In Washington, work on plumbing fixtures requires a WA-certified plumber (RCW 18.106). Electrical work, including like-for-like light, fan, switch and outlet replacement done for hire, requires a licensed electrical contractor (RCW 19.28). We don't do these jobs ourselves:

  • Electrical: light fixtures, ceiling fans, switches, outlets, dimmers, hardwired smoke detectors, bath exhaust fans, hardwired range hoods, line- or low-voltage thermostats, wired doorbells and cameras, in-wall power or data/TV cabling
  • Plumbing: faucets, toilets (including tank parts), garbage disposals, dishwashers, water heaters (gas or electric), shut-off valves, supply lines, drains
  • Gas: any gas appliance or piping

What we do: coordinate a licensed partner and handle the related carpentry, drywall and paint at menu prices.

Custom work: the not-to-exceed (NTE) quote

For anything not on this menu:

  1. Estimate. Send photos or video for a free estimate, or book a $59 on-site visit.
  2. Written quote within 1 business day. It lists the scope, the items, what's excluded and the materials. It is either:
    • a Fixed Price, or
    • a Not-to-Exceed ceiling: time at $89/hr plus materials, never more than the cap. If we finish under, you pay less.
  3. No surprises. We never go over the ceiling without your written approval (text or email) of a change order before the extra work starts.
  4. Hidden problems such as rot or water damage: we stop, photograph it, explain your options and give you a revised ceiling. You decide.
  5. Itemized invoice with before/after photos and material receipts.
  6. Deposits and disclosures. No deposit on jobs under $1,000. Special-order materials only on larger jobs. For residential jobs over $1,000, we provide Washington's required contractor disclosure statement before work starts.

For real estate agents & sellers: Inspection-Repair Sprint

  • Send the inspection report (PDF) or repair addendum. You get an itemized quote within 1 business day, keyed to the report's item numbers. Licensed-trade items are flagged with partner referrals.
  • Work starts within 3 business days or by your deadline. Rush (within 48 hours): +$75.
  • Pricing: menu prices per item; everything else on an NTE quote; no coordination fee.
  • Tear-out items from the report (wet drywall, damaged carpet, rotted fence or deck sections) are priced from the Demo & Haul-Away section, with haul-away included. We'll ask for the asbestos survey or statement up front so it doesn't hold up your deadline.
  • Listing-Ready blocks for pre-listing punch lists: Half Day $399 (4 hours, 1 technician) · Full Day $719 (8 hours). Materials extra.
  • What you get: lockbox access and direct coordination with the seller or occupant; text updates to the agent; before/after photos per item; a completion letter and invoice itemized by report item, ready to forward to the buyer's agent

For property managers & landlords: Turnover Package

Unit size Price Labor included
Studio / 1BR $349 up to 4 hr
2BR $469 up to 5.5 hr
3BR+ / single-family $619 up to 7 hr
  • Standard turnover punch list: nail-hole fill and small patches (ready to paint); door, cabinet and hardware adjustments; blind replacement (supplied or at cost); kitchen/bath caulk; smoke/CO alarm test and battery-only replacement; bulbs, HVAC filter, cover plates; minor fence and gate repair; a dated photo report
  • Make-ready demo and haul-away add-ons at menu prices (Demo & Haul-Away section): carpet and pad out $199 first room / +$89 each additional, damaged drywall out $249 per wall, appliance haul-away $69, debris loads $219 / $339 / $549. Trash-outs of tenant-left belongings are referred to a licensed hauler.
  • Extra time at the PM rate of $85/hr. Materials at cost + 10%.
  • Service levels: work orders acknowledged within 2 business hours (Mon–Sat); standard work orders scheduled within 2 business days; turnovers started within 3 business days of key access; urgent (non-emergency) work orders next business day; Saturday at standard rates
  • Approval limit: you set a not-to-exceed per work order (default $350). We get approval before going over.
  • Invoices itemized per property and unit with your work-order number. Monthly consolidated statement available.

Aging-in-place safety add-ons

Option Price What's included
Safety Walk-Through $119 60–75 minute room-by-room check of falls, lighting, grab points, entries and stairs; written, prioritized list with photos
Safe Bath Starter $229 + grab bars 2 grab bars (tile +$29/bar), non-slip tub treads, plug-in motion night-lights set up
Safe Steps & Entry $309 + materials Interior handrail up to 12 ft, anti-slip stair treads, 2 battery motion lights
Knob-to-lever conversion $79 first door, +$29 each additional Lever handles installed (your hardware or at cost)

These are practical home-safety improvements, not medical advice. We're happy to work from an occupational therapist's recommendations.

Licensed, bonded & insured · WA L&I #APEXLLL749PO

Book onlineCall (206) 739-1809
Apex Local LLC

Home services and handyman work for homeowners, realtors and property managers across Snohomish County and the greater Puget Sound.

SERVICESWORKPRICINGBLOGBOOK NOWABOUTCONTACT
(206) 739-1809 operations@apexlocal.us 8619 53rd Pl W,
Mukilteo, WA 98275
Mon–Sat, 9:00am – 6:00pm @apexlocalllc Apex Local on Facebook

© 2026 Apex Local LLC. All rights reserved.

Licensed, bonded & insured · WA L&I #APEXLLL749PO.
Home services provider serving Snohomish County and the greater Puget Sound.